About

Not another
lamp.

The lamp generator

A studio that makes lamps
nobody else has.

Not Another Lamp is a design studio in your browser. Stack shapes into a sculpture, crown it with a hat, watch it glow — and download files that print without supports, sized for the socket and bulb you actually have.

Hi, I'm Triantafyllos Samaras (Rose). I got my first 3D printer in December 2025. Not Another Lamp is the studio I built to design our lamps — and now you can use it too.

The Cubist lamp from the studio, glowing on an oak desk
The Cubist preset — a 3D preview from the studio.

21

shapes to build with

12 × 12

hat shapes × surfaces

7

kinds of lamp and object

0

supports needed

How it works

Five steps from idea to light.

01

Stack

Pick shapes and stack them into a sculpture: move, turn and tilt each one in 3D, or start from a premade mix.

02

Crown

Choose a hat: drum, bell, globe, pagoda and more, smooth or pleated, ribbed, knitted or scaled.

03

Light

Switch the lights off and see it glow on oak, marble or linen, with the real bulb and socket inside.

04

Download

Get one 3MF per print plate with the settings already set, STLs, and a README with the parts list and assembly steps.

05

Print

Every overhang has a 45° underside, so it prints upright with no supports. A fit test comes first.

What you can make

Seven kinds of light — and one that isn't.

Table lamps

A sculpture with a hat on top. The socket goes in from below and the cable leaves through a slot at the back.

Bare-bulb lamps

A globe or filament bulb on show, clamped on the top ledge.

Hanging lamps

The same lamp, upside down: the cord drops into the light shaft and the hat hangs underneath.

Wall lamps

A relief on a back plate with keyholes. It prints lying flat; the cable runs straight into the wall.

Glass bases

Measure a hurricane, jar or globe and the base is cut to hold it, even sunk deep into the sculpture.

Candle holders

A pocket for a bought metal cup on pads and ribs, with an air gap and candle safety notes.

Sculptures

No electrics at all: an art object with your name or logo engraved underneath.

Built to print

Every file is cut
to fit the next part.

Prints without supports

Overhangs get stepped 45° undersides, checked layer by layer.

Walls slicers keep

Pleats and ribs stay full thickness on every face, so nothing goes missing in the slicer.

Ready for your printer

Per-part walls, infill and layer height for Bambu Studio and Orca, plus STLs for any slicer.

Many colours, one print

Give each block its own Bambu filament for an AMS or tool changer; the README lists the slots.

Your name underneath

Engrave text and your logo into the foot, mirrored to read from below.

My hats and My bases

Save a hat or a whole sculpture and reuse it on your next lamp.

Real parts in the preview

E27, E26, E14 and E12 sockets, the bulb you chose and the cord, drawn to size.

Fits your printer

A bed check for 11 printers; tall necks split into parts that fit.

Why a generator

A downloaded lamp vs. Not Another Lamp

A lamp modelNot Another Lamp
DesignsOne fixed designUnlimited: every lamp is yours
Fits your socket and bulbHope it doesBuilt around E27, E26, E14 or E12 and the bulb you pick
SupportsOften neededNever: 45° undersides on every overhang
ColoursAs designedAny Bambu filament per block
Your name or logoNoEngraved underneath
Selling printsDepends on the licenceIncluded in the Commercial plan

The journey

From one printer to a lamp studio.

  1. 5 Dec 2025

    The first printer

    A Bambu Lab H2S on the desk in Athens, and a lot of experiments.

  2. Dec 2025

    3DPlotter

    The first tool: turn any 3D printer into a pen plotter, with no calibration headaches.

  3. Nov 2026

    A lamp generator

    The lamp generator, first under the working name Lumen: pattern and photo lamps, then the sculpture studio.

  4. 18 Nov 2026

    The studio goes online

    Accounts, lifetime plans, and lamps built on our servers.

  5. 19 Nov 2026

    Not Another Lamp

    A name that says what it does: no two lamps the same.

Prints the first time

Every file is sliced in our tests before it reaches you. A failed print is a bug.

Yours, not ours

You design the lamp. Change anything, keep the files, engrave your name.

Safe by default

LED bulbs only, certified cord sets, and the safety notes in every download.

Always improving

New shapes, hats and fixes every week, all listed in the changelog.

Questions

Good to know.

Which printers does it work with?

Any FDM printer. Downloads include 3MF projects with the settings set for Bambu Studio and Orca Slicer, and STLs for any other slicer. An AMS is only needed for multi-colour prints.

Do I need supports?

No. Every overhang gets a 45° underside, so sculptures print upright. Hats print with two perimeters and the fitter floor built in.

Which bulbs and sockets can I use?

LED bulbs only — never incandescent or halogen in a printed lamp. The studio supports E27, E26, E14 and E12 sockets with a certified cord set; the README lists what to buy.

Do I need to know CAD?

No. You stack shapes, pick a hat and download. Everything is sliders, tiles and dragging in 3D.

Can I sell the lamps I print?

Yes, with the Commercial plan: sell the physical prints at markets, on Etsy or as commissions. The digital files themselves are never for sale or sharing.

How do I get help?

Write to [email protected] for anything about the studio, downloads or a print that went wrong, and [email protected] for everything else.

What does lifetime access mean?

One payment, no subscription: your plan stays on your account for as long as the service runs.

Make a lamp nobody else has.

Design it tonight, print it tomorrow.

Open the studio

LED bulbs only.